Screen

This product is a low viscosity, water soluble green block-out designed to fill the open areas of the screen not covered by the emulsion. Use for masking several designs on a screen until ready to print or for multi-color work.

I   When the screen is dry and free of contaminants, pour Quik-Dry® on the print side of the screen. Spread over the open areas of the screen until completely filled.

II  Touch up all defects, including heavy blobs which tend to dry on the outside and pop off or smear during printing. Where very fine meshes are used, you may reduce the viscosity by adding a little water.

III Remove blockout with water.

The small format, manual precision sharpener for screen printing squeegees 20” (51cm) or less. This portable table-top design fits anywhere and comes equipped with a single industrial strength diamond sharpening wheel.

ProChem® DXP PINK is a fast drying dual cure photo-emulsion and is recommended for textile printing with Solvent inks, UV ink systems, Plastisol, and short run Water Based inks. ProChem® DXP PINK also has a very high solid content which makes for stronger durability and better resolution. Diazo is added normally, first by adding room temperature water, agitating, and then adding the solution to the emulsion. Allow the emulsion to stand for at least 2 hours to ensure any air bubbles introduced during mixing are released. Reclaiming ProChem® DXP PINK is easy with CCI Stencil Removers, which are available in concentrate and ready-to-use formulas.

ProChem® HXT is a blue colored, one part ready-to-use emulsion, for both graphic and textile applications. It offers durability, excellent image quality and superior coating characteristics. Due to its hybrid dual-cure/pre-sensitized formula, ProChem® HXT produces sharper edges and unsurpassed resolution. This product is pre-sensitized and does not require the addition of Diazo. Reclaiming the screen when using ProChem® HXT is easy with CCI Stencil Removers, which are available in concentrate and ready-to-use formulas.

Ideal for screen printing and embroidery. Works equally well for flash-cure applications. Bonds to cloth, paper, cardboard, acetate, foil, plastic film, cork, foam rubber, and leather. Works best at room temperature.

ProChem® VPR is a one part, ready-to-use textile emulsion, and is recommended for plastisol and water based inks. It offers durability and excellent image quality. Due to the product’s high solids it yields a better coating, sharper edges and excellent resolution. ProChem® VPR is pre-sensitized and does not require the addition of Diazo. This product saves time as it exposes very fast. Reclaiming the screen when using ProChem® VPR is easy with CCI Stencil Removers, which are available in concentrate and ready-to-use formulas.

ProChem® WR-25 is a Diazo Sensitized Photo-Emulsion recommended for plastisol and water-based inks. ProChem® WR-25 has excellent water resistance. Diazo is added normally, first by adding room temperature water, agitating, and then adding the solution to the emulsion. Allow the emulsion to stand for at least 2 hours to ensure any air bubbles introduced during mixing are released. Reclaiming is easy with CCI STENCIL REMOVERS, which are available in concentrate and ready to use formulas.

These stainless steel long lasting tempered registration guides are used for any thin stock printing application. Simply tape guides into position on the printing bed and slide stock into the same place for perfect registration, print after print. Designed for manual screen printing or semi-automatic presses.

Single temperature Thermopaper non-adhesive indicators provide a faster response time and are for use when a clean and dry test surface is available. Strips consist of a temperature sensitive element that produces a non-reversible white to black color change at the rated temperature. The non-adhesive labels are available in packages of 16 strips each.

• Stops squealing, sticking, and binding of machinery
• Dries rapidly; leaves no greasy or oily film
• Retards corrosion; makes cleaning easier and quicker
• Protects and preserves equipment
• Saves time and labor
• Speeds cutting and sewing; facilitates fabric flow
• Prevents power tools from binding
• Long lasting residual performance

Why use pellons when you can use the same fabric that the t-shirt was made of?
We spread and cut Test Print Material,(Strike Off), in fabric size ranging from 15″ to 32″ wide and 22″ long.
Test tubes are sold in 25lb boxes in assorted Lights, assorted Darks, White , Black , Navy and Gray Heather.

Expert Test Squares (Pellons) are designed not to shrink when flash-cured or ran through a dryer. Black is a true black, not the traditional charcoal. Two sizes, both in a medium weight assure performance similar to most shirts printed. Very Economical.  15″ x 15″ Available in White and Black.