×

+800 505 4900 Our lines are open:
Screen Inks

Screen Inks

(52)
    • - 76 %
    On backorder

    For extremely stretchy fabrics such as Lycra/Spandex or any non-dyed polyester fabric, where an improvement in elasticity is required.
    Stencils: Avoid using water-resistant emulsions as they can react with the components used to manufacture Unistretch and cause the ink to lock-up and clog the mesh openings. Any other solvent resistant direct emulsions or capillary films will be acceptable.

    • In stock
      ES0138 NPT HD CLEAR is formulated as a press-ready plastisol for printing on 100% Cotton fabrics or over a low bleed underlay on poly/cotton. This product has excellent edge definition when stacked for that 3D look and provides maximum gloss when fully cured.Fast shearing action means higher press speeds.Can be tinted with up to 30% C3 NPT Color Boosters to make Gel Colors.High gloss and clarity when printed in thick film and cured properly.
      • In stock
        $577.20
        ES0247 NPT Soft Density Base can be printed through a wide range of mesh counts and thick film emulsions. Soft Density’s very short body and mid range viscosity mark it easy to mix, easy to print and easy to create very soft High Density type designs. Extremely precise edge definition is possible, making NPT Soft Density a good choice to reproduce prints that look like they have been die cut.Create thousands of shades by using Color Booster formulas from the M2007 Software (use C3’s at no more than 40%).Print very thick, die cut type designs.Extremely soft with less hand than most High Density inks.
        • In stock
          EA0055 is a puff concentrate. Use at up to 15% by weight to make a puff ink from any NPT opaque plastisol color. Mix thoroughly. EA0055 may also be used to take the gloss from plastisol ink. Add 2% by weight to an NPT plastisol ink to make a matte finish.
          • In stock
            Mix EA0015 at 3% by weight into the wet plastisol to eliminate gloss after it is cured. Use it at 10 to 15% to create suede looking plastisol. This product will not cure and should always be mixed in the correct ratio with a base.
            • In stock
              ES0137 NPT Sponge Puff was developed as a soft hand puff product for creating a soft, more durable puff print.Press ready plastisol for printing on dark 100% cotton and over a low bleed under lay.Colors created by using C3 Color Boosters at up to 50%.
              • In stock
                ES Sparkle Silver gives a festive look to otherwise flat, boring print designs. Use this glitter to decorate the garment for festive occasions and special events. The large particle glitter flake provides plenty of sparkle and glimmer.
                • In stock
                  ES NPT Jewel Tone is formulated as a press-ready plastisol for printing on 100% Cotton or poly/ cotton. The NPT Jewel Tone Silver can be colored to produce an array of metallic colors.
                  • In stock
                    ES4779 NPT Metallic Gold and other ES NPT Metallic products are formulated as a press-ready plastisol for printing on 100% cotton or poly/cotton.
                    • - 35 %
                    On backorder

                    Coro-Plast (CO8) series ink has been specifically formulated to a wide range of substrates. Outstanding features of this ink include: 

                    • Exceptional rewetting characteristics in the screen
                    • Good and sure drying without blocking when stacked 
                    • Very good appearance of printed ink film without surface defects
                    • Outstanding resistance to weather exposure 
                    • Very good light fastness 
                    • Wide range of substrate suitability
                    • Dubuit ECO-System Color Matching Formulations
                    • Print by hand, semi-automatic or automatic equipment

                    • - 97 %
                    On backorder
                    • - 96 %
                    On backorder
                    Union’s Tru-Tone Process inks are highly suitable for extremely accurate and consistent 4-color process.
                    • - 99 %
                    On backorder
                    • - 98 %
                    On backorder
                    • - 71 %
                    On backorder
                    Suede Plastisol Ink combines an extremely matte finish with a fuzzy texture and slightly raised effect. The resulting print is almost indistinguishable from suede leather in texture and appearance.
                    • - 95 %
                    On backorder
                    Direct printing on light or dark garments. Stencils: Use any direct emulsion or capillary film. Additives: Shimmer Metallic inks are supplied readyto print Reducer/Detackifier (PLRE-9000) may be add-ed if a thinner consistency is required. Curing Instructions: These inks will cure at 300 F (149 C.). Because of the relfective nature of this ink, it requires a longer curing time under the heat to reach the required temperature than standard plastisols. PRODUCTS: Standard Colors PAGE-M128 Bright Silver / PAGE-M210 Bright Gold PAGE-M300 Brilliant Red / PAGE-M500 Metallic Blue PAGE-M600 Emerald Green / PAGE-M800 Sparkling Black
                    • - 94 %
                    On backorder
                    Chalkboard Plastisol is used to provide a smooth, dry surface on a garment which can be written upon with normal limestone chalk. The ink can be printed either as a direct print or as a cold peel transfer. Crayon Clear is a plastisol formulated for screen printing on heat transfer papers. After semi-curing, the printed surface provides a base for drawing messages or designs, using crayons or felt-tipped pens.
                    • - 94 %
                    On backorder
                    Union Ink Glitter Plastisols are recommended when printing directly on fabrics, where they give just as brilliant results as when using the more expensive Super Glitters. They are suitable for transfer printing but yield less brilliant results than Super Glitters.
                    • - 99 %
                    On backorder
                    • - 73 %
                    On backorder
                    Holographic Glitter Plastisol is a series of intense sparkling, glitter colors. Designs will have the appearance of a multi-colored glitter when direct sunlight or a point light source is reflected off the holographic particles.
                    • - 79 %
                    On backorder
                    Flash-Back ink is an easy to use, one-part, plastisol ink that contains millions of light-reflecting microspheres. In daylight the ink appears to be a normal print. In other words, gray ink appears gray, and red ink appears red. However, when a Flash-Back print is exposed to a focused beam of light such as an automobile headlight or a flashlight, it reflects a bright, glittering image back at the light source.
                    • On backorder
                      NPT Soft Density Base can be printed through a wide range of mesh counts and thick film emulsions. Soft Density’s very short body and mid range viscosity mark it easy to mix, easy to print and easy to create very soft High Density type designs. Extremely precise edge definition is possible, making NPT Soft Density a good choice to reproduce prints that look like they have been die cut.Create thousands of shades by using Color Booster formulas from the M2007 Software (use C3’s at no more than 40%).Print very thick, die cut type designs.Extremely soft with less hand than most High Density inks.
                      • - 69 %
                      On backorder
                      On some nylon materials, these inks will adhere satisfactorily when reduced with 10-15 percent SOLV-1498 Reducer
                      • - 92 %
                      On backorder

                      D-Base is a clear, waterbase discharge ink. Suitable fabrics are easily discharged producing an extremely soft-hand. D-Base can be used as a color-stripping (bleaching) underbase or can be used with pigments. D-Base can be used in conjunction with other ink systems to produce multiple effects. D-Base’s rheology and flow characteristics allow it to be printed with high mesh counts. This produces very fine image detail and a softer finish.

                      U-Base is a white underbase discharge ink specifically designed for use in conjunction with plastisol and water-based inks. U-Base is used as a color-stripping (bleaching) underbase. The natural fabric color is replaced with a white underbase. Suitable fabrics are easily discharged producing an extremely soft-hand. U-Base’s rheology and flow characteristics allow it to be printed with high mesh counts, which produces very fine image detail and a softer finish.

                      D-Powder is a discharge activator. Stir in 3-6%, by weight, and mix well. Different percentages of the Activator will affect the discharge results; increase or decrease in order to achieve desired results. Mix only enough for current production requirements. Activated ink should be us ed within 8 hours.

                      P-Charge is an ink additive that will make Plastisol inks perform like waterbased discharge inks. The results are a softer hand and the feel of a waterbased print without having to have a separate mixing system.

                      W-Base is a clear base for waterbase printing. W-Base is designed to be used with pigment systems or as an extender for standard waterbase colors. W-Base has great color reflection for strong vivid colors when mixed with CCI’s CMS Color Mixing System.

                    We are the right partner for you

                    This is why