×

+800 505 4900 Our lines are open:

Textile Inks

(44)
    • - 76 %
    On backorder

    For extremely stretchy fabrics such as Lycra/Spandex or any non-dyed polyester fabric, where an improvement in elasticity is required.
    Stencils: Avoid using water-resistant emulsions as they can react with the components used to manufacture Unistretch and cause the ink to lock-up and clog the mesh openings. Any other solvent resistant direct emulsions or capillary films will be acceptable.

    • In stock
      $577.20
      ES0247 NPT Soft Density Base can be printed through a wide range of mesh counts and thick film emulsions. Soft Density’s very short body and mid range viscosity mark it easy to mix, easy to print and easy to create very soft High Density type designs. Extremely precise edge definition is possible, making NPT Soft Density a good choice to reproduce prints that look like they have been die cut.Create thousands of shades by using Color Booster formulas from the M2007 Software (use C3’s at no more than 40%).Print very thick, die cut type designs.Extremely soft with less hand than most High Density inks.
      • In stock
        Mix EA0015 at 3% by weight into the wet plastisol to eliminate gloss after it is cured. Use it at 10 to 15% to create suede looking plastisol. This product will not cure and should always be mixed in the correct ratio with a base.
        • In stock
          ES0137 NPT Sponge Puff was developed as a soft hand puff product for creating a soft, more durable puff print.Press ready plastisol for printing on dark 100% cotton and over a low bleed under lay.Colors created by using C3 Color Boosters at up to 50%.
          • In stock
            ES Sparkle Silver gives a festive look to otherwise flat, boring print designs. Use this glitter to decorate the garment for festive occasions and special events. The large particle glitter flake provides plenty of sparkle and glimmer.
            • In stock
              ES NPT Jewel Tone is formulated as a press-ready plastisol for printing on 100% Cotton or poly/ cotton. The NPT Jewel Tone Silver can be colored to produce an array of metallic colors.
              • In stock
                ES4779 NPT Metallic Gold and other ES NPT Metallic products are formulated as a press-ready plastisol for printing on 100% cotton or poly/cotton.
                • - 97 %
                On backorder
                • - 96 %
                On backorder
                Union’s Tru-Tone Process inks are highly suitable for extremely accurate and consistent 4-color process.
                • - 99 %
                On backorder
                • - 98 %
                On backorder
                • - 71 %
                On backorder
                Suede Plastisol Ink combines an extremely matte finish with a fuzzy texture and slightly raised effect. The resulting print is almost indistinguishable from suede leather in texture and appearance.
                • - 95 %
                On backorder
                Direct printing on light or dark garments. Stencils: Use any direct emulsion or capillary film. Additives: Shimmer Metallic inks are supplied readyto print Reducer/Detackifier (PLRE-9000) may be add-ed if a thinner consistency is required. Curing Instructions: These inks will cure at 300 F (149 C.). Because of the relfective nature of this ink, it requires a longer curing time under the heat to reach the required temperature than standard plastisols. PRODUCTS: Standard Colors PAGE-M128 Bright Silver / PAGE-M210 Bright Gold PAGE-M300 Brilliant Red / PAGE-M500 Metallic Blue PAGE-M600 Emerald Green / PAGE-M800 Sparkling Black
                • - 94 %
                On backorder
                Chalkboard Plastisol is used to provide a smooth, dry surface on a garment which can be written upon with normal limestone chalk. The ink can be printed either as a direct print or as a cold peel transfer. Crayon Clear is a plastisol formulated for screen printing on heat transfer papers. After semi-curing, the printed surface provides a base for drawing messages or designs, using crayons or felt-tipped pens.
                • - 94 %
                On backorder
                Union Ink Glitter Plastisols are recommended when printing directly on fabrics, where they give just as brilliant results as when using the more expensive Super Glitters. They are suitable for transfer printing but yield less brilliant results than Super Glitters.
                • - 99 %
                On backorder
                • - 73 %
                On backorder
                Holographic Glitter Plastisol is a series of intense sparkling, glitter colors. Designs will have the appearance of a multi-colored glitter when direct sunlight or a point light source is reflected off the holographic particles.
                • - 79 %
                On backorder
                Flash-Back ink is an easy to use, one-part, plastisol ink that contains millions of light-reflecting microspheres. In daylight the ink appears to be a normal print. In other words, gray ink appears gray, and red ink appears red. However, when a Flash-Back print is exposed to a focused beam of light such as an automobile headlight or a flashlight, it reflects a bright, glittering image back at the light source.
                • On backorder
                  NPT Soft Density Base can be printed through a wide range of mesh counts and thick film emulsions. Soft Density’s very short body and mid range viscosity mark it easy to mix, easy to print and easy to create very soft High Density type designs. Extremely precise edge definition is possible, making NPT Soft Density a good choice to reproduce prints that look like they have been die cut.Create thousands of shades by using Color Booster formulas from the M2007 Software (use C3’s at no more than 40%).Print very thick, die cut type designs.Extremely soft with less hand than most High Density inks.
                  • - 69 %
                  On backorder
                  On some nylon materials, these inks will adhere satisfactorily when reduced with 10-15 percent SOLV-1498 Reducer
                  • On backorder

                    Curable Thinner is used to thin plastisol inks. It can be mixed into the product at any level necessary to achieve the desired printability. Keep in mind that the more of any thinner you add to ink, you are reducing the opacity and other properties of the product such as low bleed. The mixture can print through a wide variety of mesh ranges and will cure at 320 degrees F (160 degrees C).

                    • - 76 %
                    On backorder
                    Nylobond is an additive which, when mixed with Union Ink Plastisol Colors, will provide adhesion to most water-proofed nylon jackets and other garments. Extensive tests have shown that Nylobond is effective with all Union Ink Plastisols: However, the PLUS and PATH series inks give the best results with very good opacity.
                    • - 94 %
                    On backorder
                    Unilon is a hot-melt adhesive powder used to improve the adhesion of plastisol heat transfers to nylon, polyester and other synthetic garments, including those with water-proof coatings. Unilon powder is also used to increase the adhesion and washability of foil transfers.
                    • - 94 %
                    On backorder
                    This is the industry standard in Plastisol Reducer/Detackifier. If you’re having a hard time pushing ink through your screen, you may need to reduce it. If you are getting ink buildup on the bottom of your screens you may need a detackifier. Don’t use chemicals like mineral spirits to reduce your ink. They will throw your inks out of balance and cause them to not cure properly! PLRE 9000 is the new PLUS 9000. It is now phthalate-free to meet up with the new industry standards. If you print on any youth sized garments, they must be printed with phthalate free inks and additives!

                  We are the right partner for you

                  This is why