×

+800 505 4900 Our lines are open:

Specialty Inks

(16)
    • - 76 %
    On backorder

    For extremely stretchy fabrics such as Lycra/Spandex or any non-dyed polyester fabric, where an improvement in elasticity is required.
    Stencils: Avoid using water-resistant emulsions as they can react with the components used to manufacture Unistretch and cause the ink to lock-up and clog the mesh openings. Any other solvent resistant direct emulsions or capillary films will be acceptable.

    • In stock
      Mix EA0015 at 3% by weight into the wet plastisol to eliminate gloss after it is cured. Use it at 10 to 15% to create suede looking plastisol. This product will not cure and should always be mixed in the correct ratio with a base.
      • In stock
        ES Sparkle Silver gives a festive look to otherwise flat, boring print designs. Use this glitter to decorate the garment for festive occasions and special events. The large particle glitter flake provides plenty of sparkle and glimmer.
        • In stock
          ES NPT Jewel Tone is formulated as a press-ready plastisol for printing on 100% Cotton or poly/ cotton. The NPT Jewel Tone Silver can be colored to produce an array of metallic colors.
          • In stock
            ES4779 NPT Metallic Gold and other ES NPT Metallic products are formulated as a press-ready plastisol for printing on 100% cotton or poly/cotton.
            • - 71 %
            On backorder
            Suede Plastisol Ink combines an extremely matte finish with a fuzzy texture and slightly raised effect. The resulting print is almost indistinguishable from suede leather in texture and appearance.
            • - 95 %
            On backorder
            Direct printing on light or dark garments. Stencils: Use any direct emulsion or capillary film. Additives: Shimmer Metallic inks are supplied readyto print Reducer/Detackifier (PLRE-9000) may be add-ed if a thinner consistency is required. Curing Instructions: These inks will cure at 300 F (149 C.). Because of the relfective nature of this ink, it requires a longer curing time under the heat to reach the required temperature than standard plastisols. PRODUCTS: Standard Colors PAGE-M128 Bright Silver / PAGE-M210 Bright Gold PAGE-M300 Brilliant Red / PAGE-M500 Metallic Blue PAGE-M600 Emerald Green / PAGE-M800 Sparkling Black
            • - 94 %
            On backorder
            Chalkboard Plastisol is used to provide a smooth, dry surface on a garment which can be written upon with normal limestone chalk. The ink can be printed either as a direct print or as a cold peel transfer. Crayon Clear is a plastisol formulated for screen printing on heat transfer papers. After semi-curing, the printed surface provides a base for drawing messages or designs, using crayons or felt-tipped pens.
            • - 94 %
            On backorder
            Union Ink Glitter Plastisols are recommended when printing directly on fabrics, where they give just as brilliant results as when using the more expensive Super Glitters. They are suitable for transfer printing but yield less brilliant results than Super Glitters.
            • - 99 %
            On backorder
            • - 73 %
            On backorder
            Holographic Glitter Plastisol is a series of intense sparkling, glitter colors. Designs will have the appearance of a multi-colored glitter when direct sunlight or a point light source is reflected off the holographic particles.
            • - 79 %
            On backorder
            Flash-Back ink is an easy to use, one-part, plastisol ink that contains millions of light-reflecting microspheres. In daylight the ink appears to be a normal print. In other words, gray ink appears gray, and red ink appears red. However, when a Flash-Back print is exposed to a focused beam of light such as an automobile headlight or a flashlight, it reflects a bright, glittering image back at the light source.
            • - 94 %
            On backorder
            Union Ink Glitter Plastisols are recommended when printing directly on fabrics, where they give just as brilliant results as when using the more expensive Super Glitters. They are suitable for transfer printing but yield less brilliant results than Super Glitters.
            • - 99 %
            On backorder
            Plastipuff is a plastisol puff ink formulated to cure and expand rapidly. It also produces an exceptionally strong, long-lasting ink film with a high uniform finish and excellent abrasion resistance. The inks should be used on T-shirts, sweatshirts and other woven cotton and cotton/polyester garments.
            • - 74 %
            On backorder
            Mix up to 5% NPT Tack Free additive into a NPT ink to reduce the wet ink tack for easier printing and the after tack (Hot Tack) after a flash. Adding NPT Tack Free additive will reduce the bleed characteristics of Low Bleed inks and increase the flash cure time depending on how much is used.
            • On backorder
              ES0026 NPT ThermoLine Clear is a non-phthalate plastisol used for adhesive type applications and as a clear base for Metallic powders and flakes.

            We are the right partner for you

            This is why