This product is a super concentrated formula for degreasing and wetting all types of screen fabrics, including polyester, nylon and stainless steel. When completely water rinsed, TABS II leaves your fabric free of silicones or other types of oils that tend to leave slippery active surface. TABS II will also reduce incidence of pin holes. Use this solution for degresing new fabric of all types before stencil making.
I Prior to using, remove any ink or stencil residue.
II Use concentrated or can be dilute up to 1:20 with water. Brush liquid degreaser on both sides of the screen.
DEGREASER 1:20 Concentrate is an economical degreaser with strong foaming action. It is free from Chlorine and phosphates, and is biodegradable. One quart of DEAGREASER 1:20 concentrate makes 5 gallons of working degreaser solution.
An abrasive degreaser gel that combines the actions of No. 2 and No. 3.
The abrading action of Ulanogel 23 promotes better wetting of the fabric and adhesion of the stencil, and thus, longer
press life. Its degreasing action removes dirt, dust, and oils from the fabric, reducing the risk of stencil failure and
COMBINED LIQUID SCREEN DEGREASER, WETTING AGENT, AND ANTISTATIC TREATMENT
Magic Mesh Prep is a ready-to-use liquid combining the properties of mesh degreaser, wetting agent, and anti-static treatment. Magic Mesh Prep improves the flow characteristics of liquids, facilitating more uniform coating of direct emulsions and the easier transfer of ink during printing, thereby improving printed image quality.
A degreaser solution that removes dirt, dust and oils from all meshs, new and used.
Degreasing should be considered a first step in stencil-making, as it greatly reduces the risk of stencil-making failure, extends on-press stencil longevity, and alleviates pinholing. Screen Degreaser Liquid No. 3 is ready-to-use--no mixing. Degreases effectively in hard water. Rinses clean with hot or cold water. Non-caustic--will not harm frames, mesh, or adhesives on stretch and glue frames. Reccomended for use with all Ulano stencil systems.
This is a super concentrated formula for degreasing and wetting all types of screen fabrics, including polyester, nylon and stainless steel. When completely water rinsed, NUTRALYZE® leaves your fabric free of silicones or other types of oils and contaminants that tend to leave a film or slippery active surface. NUTRALYZE® will also reduce incidence of pin holes. Use this solution for degreasing new or used fabric of all types before stencil making. NUTRALYZE® can be used in concentrated form, or it can be diluted 1 to 10 with water.
This product is a vicious dehazer and degreaser that is designed for a variety of inks. Stain-X cleans mesh of stains with less noticeable odor and works better than most hazardous stain removers. Stain-X leaves your fabric free of all oils and contaminants, which will reduce the incidence of pinholes.
I Before using Stain-X, remove all ink residue and emulsion from the screen.
II Brush product on the ink side of a WET screen. Agitate on both sides of the screen with a brush or pad and set aside for approximately 1 to 10 minutes.
III High pressure water rinse, spraying from the bottom to top, on the print side of the screen. Reverse screen and high pressure rinse, then use low pressure water and flood rinse the complete screen. Allow screen to dry before coating.
Elite Combo Dehaze & Degreaser is an enviromentally approved, 100% active, low odor extremely quick penetrating and fast acting solvent designed to dissolve and clean all types of screen printable inks, adhesives, clear coatings and stains from printing mesh. Elite Combo Dehaze & Degreaser works quickly and causes no damage to printing mesh.
MULTI-WASH is a water soluble screen wash designed for the removal of all inks, including plastisol and UV inks. This product works especially well on tough inks such as: water base, vinyl, epoxy and enamels. This Product can also be used for the removal of stubborn cured ink stains (ghost / image).